Slash Pipes Installation Directions

 

V-862 VICTORY SLASH PIPES FOR 2005 – PRESENT HAMMER & JACKPOT MODELS
V-872 VICTORY SLASH PIPES FOR 2006 – PRESENT VEGAS & KINGPIN MODELS & 2011-PRESENT VICTORY HIGH BALL

 

  Thank you for purchasing this RPW USA product. We believe that our products are the very best available and are engineered to provide a lifetime of use. These RPW Slash pipes can be installed on Victory Hammer & Jackpot models from 2003 to present, Victory Vegas & Kingpin models from 2006 to present and Victory High Ball 2011 to present. Basic hand tools and a service manual applicable to your model of motorcycle are all that is necessary to complete the installation.

BILL OF MATERIALS

Part # Quantity Description 

 1 Front pipe, chrome 

 1 Rear pipe, chrome

1 Front heat shield, chrome 

 1 Rear heat shield, chrome 

 1 Mounting bracket 

 2 Baffles 

 4 Exhaust clamp half 

 5 Hose clamp, stainless steel 

 2 1/4” – 20 hex nut, stainless steel 

 2 1/4” washer, external star 

 2 5/16” – 18 x 1” button head cap screw, stainless steel 

 2 1/4” - 20 x ½” button head cap screw, stainless steel 

 2 5/16” lock washer 

 4 5/16” flat washer 

 2 5/16” – 18 hex nut, stainless 

 1 3/8” flat washer 

 1 Set of instructions

1 Warning Label



MAINTENANCE TIP: To keep your new Slash pipes looking their best, we recommend applying a high-quality chrome polish to them every time you detail your motorcycle.

Please Note: Pipes are not warranted against bluing and UNDER NO CIRCUMSTANCE will pipes be warranted after they have been run on an engine. See TUNING TIP in Step 9.

STEP 1: Begin by removing the existing pipes from the motorcycle, and then inspect the exhaust gaskets. If they are worn or deteriorated, fit the engine with a new set.

STEP 2: Installation of Slash pipes requires the lower frame rail to be cut off as shown. Deburr the frame rail with a file or burr knife to leave a smooth edge and cover any bare metal with touch-up paint to prevent rust.






STEP 3: Following the procedure outlined in the appropriate service manual for your year and model of motorcycle, remove the swing arm pivot shaft nut. Place the rear mounting bracket over the pivot shaft making sure that the 3/8” washer (inset) is placed inside the bracket as shown. Tighten the pivot shaft nut while orienting the mounting bracket facing the rear of the bike, parallel to the ground as shown.





STEP 4: To install the heat shields, slip the supplied hose clamps through the hoops welded onto the backside of each shield as shown. Install the heat shields onto the pipes and tighten all hose clamps evenly, aligning the shields with the exhaust pipes for proper fit.







STEP 5: The baffles can be installed prior to mounting the pipes to your motorcycle, or once the pipes are in place. Slip the baffles in with the pointed end in first and secure with hardware provided in this kit. Place one external star lock washer on each screw on the inside of the pipe next to the nut.






STEP 6: The front pipe must be carefully “snaked” in past the engine and foot controls as shown. Work the pipe in slowly and carefully to avoid scratching the chrome or finish.









STEP 7: Split exhaust clamps are included for both pipes. They are oriented as shown in the inset photo and can be installed on the engine one half at a time. As shown in the main photo this greatly helps the installation of the front pipe. Repeat this process for the rear pipe installation and snug all exhaust flange nuts, but do not tighten them completely.





STEP 8: Attach the pipes to the rear mounting bracket with the supplied hardware. (Note: 2008 and up Vegas models, using the supplied hardware slip aluminum spacers in place on rear mounting bracket and then attach the pipes to the rear mounting bracket.) Once the pipes are aligned correctly, tighten all hardware as specified by the specifications listed in the appropriate service manual for your year and model of motorcycle.





STEP 9: Prior to starting the engine, wipe the pipes down with lacquer thinner or acetone on a clean rag. Start your engine and check for exhaust leaks. You are now ready to enjoy your RPW USA Slash exhaust pipes. Installation of this exhaust will require the use of the Victory Stage 1 Performance CPU re-flash. See your Victory dealer for details.

TUNING TIP – To help prevent bluing, the engine should be properly tuned before running it with the new exhaust. We recommend for an Adjustable Fuel Tuner . 

CARE & MAINTENANCE   

This bike is equipped with an RPW USA exhaust.  RPW USA strives to offer the highest quality exhaust pipes.  However, these pipes require care and maintenance.  The following tips are suggested to insure years of service of your Chrome / Ceramic-Coated Exhaust System.

OWNER & DEALER CARE INSTRUCTIONS:  After Installation and Before Engine Run Remove grease and/or skin oils from the exhaust surface.  Stains & fingerprints will show when exhaust gets hot. 

CARE INSTRUCTIONS:Chrome:  Wipe down exhaust with rubbing alcohol and a soft cloth, dry thoroughly.Ceramic Coated:  Wipe the tubes down with a mild soap, warm water and a soft cloth, dry thoroughly.

 WARNING - Never wash exhaust pipes when they are warm or hot.